A roof cleans up well when the method matches the material, and badly when it doesn’t. Terracotta and concrete tiles, and Colorbond steel, each grow their own kind of grime and each tolerate a different amount of pressure, water and chemical. This guide explains how each is cleaned, what to avoid, and when a soft wash is the right call.
“We had a pipe burst in our ceiling, water seeped into our walls and our unit was at a very high risk for mould :( Guosheng worked tirelessly to ensure the drying process went as smooth as possible, even working until the evening on a Friday to ensure our walls would be dry and safe over the weekend! An extremely proficient and productive company that thrives on providing excellent service and quality work. Thank you so much for all of your help! <3”
“Guosheng from Elite Restoration did an amazing job dealing with the water damage to my unit, due to a burst pipe. Nothing was too hard and Guosheng had multiple tricks up his sleeve to ensure maximum drying capacity. The communication throughout the whole process was excellent, which made this very stressful situation for me a lot easier to handle. Thanks so much Guosheng.☺️”
Elite provides specialist cleaning and restoration for the BMS National Rugby Training Centre at Ballymore as a valued partner of Queensland Rugby Union.
Lichen, moss and black algae settle on the shaded, south-facing side first, feeding on moisture and the dust that blows in. Leaf litter from overhanging trees traps water and speeds it up. Left alone, lichen roots into a tile’s surface and algae streaks a steel roof, and both hold moisture against the roof for longer after rain.
Concrete and terracotta tiles
What pressure does to a tile
A concrete tile is porous, and its colour is a thin surface layer. High pressure held close strips that layer, leaves the tile bare and chalky, and shortens its life. Terracotta is harder but its glaze can chip, and old tiles crack when they are walked on wrongly. Pressure also drives water under the tiles and into the roof cavity.
How tiles are cleaned
The usual method is a soft wash: a cleaning solution applied at low pressure, left to work on the lichen and algae, then rinsed. Heavy lichen is sometimes treated and left to die off over the following weeks rather than blasted. Where pressure is used at all, it is low, with a wide fan, worked down the roof so water runs with the overlaps and not under them. Ridge capping and pointing are checked, because a clean often shows up cracked mortar.
Colorbond and other metal roofs
What a steel roof tolerates
A Colorbond roof is a painted steel sheet. It takes moderate pressure well and rinses clean, but the paint can be marked by a nozzle held too close, by grit dragged across it, and by strong chemicals left to dry in the sun. Walking on it dents the pans, so the work is done from the ridges and the screw lines.
How a metal roof is cleaned
A light detergent or a soft wash solution, a rinse at moderate pressure working with the fall of the roof, and attention to the gutters, which catch everything that comes off. A metal roof dries fast and shows streaks if it is rinsed unevenly, so the rinse is done in full runs from ridge to gutter.
What the two have in common
Clear the gutters first, or the wash water backs up and overflows.
Cover or move anything below the eaves: plants, cars and outdoor furniture.
Never clean a roof in rain, high wind or full midday heat.
A wet roof is a fall risk. Roof work needs harnesses or edge protection, and a roof that is steep or high is not a job for a ladder and a hose.
Getting it done
Elite provides roof cleaning and soft washing for tile and metal roofs. Our technicians are police-checked and fully insured, we carry $20 million in public and products liability cover, and every job carries a satisfaction guarantee.
Roof cleaning questions
Can you pressure wash a tiled roof?
Not at high pressure. It strips the surface of concrete tiles and forces water under them. Tiles are soft washed, with low pressure only where it is needed.
How often should a roof be cleaned?
When lichen, moss or streaking is visible, often every few years. Shaded roofs and roofs under trees need it sooner.
Does cleaning a Colorbond roof damage the paint?
Not when the pressure is moderate and the nozzle is kept back. Harsh chemicals and dragged grit are what mark it.